Make a copy and images on T-Shirt
Print itself is a step to record / copy the image onto a movie screen. Drugs used as a 'master tinta'nya print. Drugs used were Ulano TZ / Chromatin.
Step - step is;
1.
The new screen frame should be bought, washed with soap cream beforehand using a patchwork penyikatnya, there is concern that the former liquid paint sludge to dry or dust etc., which can damage the fabric mesh screen. After being washed dried with a hairdryer (not too close because the heat will damage the fabric screen) or a fan who was not turned a pile of sand or dust that would contaminate the already washed back to the screen. Can the hot sun, but with standing screen position,
2.
While the screen is cleaned, mixed with a sensitizer Ulano, adjust to the application, if you only need one screen means no need to mix it up a bottle ulano, Ulano recommended given the mixed one drop of ink whose color is not included in the color that will be screened, to ensure easy read the details to drawings,
3.
After the screen otherwise clean and dry, seal with TZ ulano using mica or a ruler (okay to use rakel but if the result is too thick, should not use rakel), adjust the size of the image to be printed, front and rear frame of the screen,
4.
If the screen really has closed Ulano, just dry with a hairdryer (if you use the fan will be very long dry). Do not ever use any lighting, especially the hot sun to dry,
5.
After Ulano dries, move the images on the film / cliche or paper stencil printer HVS results that have been smeared by vegetable oil. By the way, put the picture on the front screen upside down, closed 5mm glass and the inside or behind a screen cushioned black fabric, lighting can be in two ways, namely;
- UV light from the Sun, the order of glass, film, screen, black fabric cushions (you can also add other ballast to pressing a pillow) faced into the sun for about 20 seconds.
- Neon Lamp Light 2 x 40watt, the same sequence but do not need anymore because there is 5mm glass on the table, if you use the copy difference table facing down towards the lamp, Solarise + 15 minutes,
6.
Once exposed, the screen flush with clean water first, and certainly there are no dust dirt / small rocks when sprayed will be damaging, not just the pictures that have been removed but the fabric screen can be damaged / torn. Also the function to soften the layers that are not exposed Ulano,
7.
Spray water with a guide that has been printed image, meaning that the details of the picture is very small easy to read. (If any detail is damaged because the water spray is too harsh, layered Ulano using Cutton bud),
8.
Once sprayed, dry with a hairdryer, because it takes the wind and heat that dries faster. If the weather is not cloudy, may just use the hot sun,
9.
Cover the edges with duct tape screen Ulano in brown, the front side image and back to avoid tembusnya ink that is incompatible with the original picture and so the ink does not go into the sidelines / corner of the screen that will be difficult to clean,
10.
Then the screen given the vise if you want to print using the table,
11.
T-Shirt that has been inserted inside plywood placed on the table under the screen, if it produces silk screening t-shirts with a vast amount, use the Mal / limiter to the size / location of the same stencil,
12.
Before the above t-shirts, use the newspaper to ensure that no undue translucent ink,
13.
Place the ink that was mixed fluid amplifier / special adhesives, inks that contain functions that rubber is not easily broken, when washed and ironed. (Can be asked to seller screen printing equipment), use rakel to flatten,
14.
If there are images in the pattern of lines on the edge of lis or letters for example, should lis printed later. Due to be adjusted if the location does not match, the way the system hold-up man / open the clamp,
15.
When you're finished, the screen should be washed immediately with soap and cream patchwork of course with a brush. Although using water-based ink, if the screen is not as difficult to clean immediately be cleaned of oil-based ink,
16.
Remove the shirt from the plywood when it is dry before confronted a fan, keep it away from the plywood seams remaining threads of convection (the inside of shirts) are attached as it may affect the results of the next sablonase.
Sunday, April 4, 2010
Subscribe to:
Post Comments (Atom)
No comments:
Post a Comment